Custom carriers from OOB's and painted pieces

  • '20 '19 '18 Customizer

    As mentioned previously, the US Navy only had two Portland class cruisers in the fleet. With that in mind, FOlewnik is modding several Portland sculpts into other classes of cruisers, starting with five of the New Orleans class. The main difference between the two classes, as shown in the below comparison of a New Orleans class cruiser silhouette taken from shipcamouflage.com vs a Portland sculpt, is that the 2nd smoke stack and the scout plane deck with launch catapults have swapped places. Pretty much everything from the 1st smokestack forward matches, and from the New Orleans’ recovery crane back matches (or will once the mod gets its crane).
    Comparison NOvsPortland.jpg

    FOlewnik’s first thought was that he needed to buy a better hobby saw, like a jeweler’s saw. But then it occurred to him that he could use the saw he has and just cut off everything starting at the back all the way up to the 1st smoke stack. In the picture below, that’s the sculpt in the upper right. That particular sculpt has a bad cut, but as you can see from the sculpt in the lower left, that gets filled with putty, and then sanded like the one in the upper left. Prior to cutting, the sculpt is cleaned of flash plastic as best as possible with an Xacto knife, the section of plastic in front of the 1st smoke stack is cleared away, and the radar hub “fin” above the bridge is cut to a nub to separate it from the rest of the tower.
    20190817_202746a.jpg
    The cut off rear deck gun, 2nd smoke stack housing and launch catapult base are saved and separated (inset above) to be glued back onto the piece, swapping the front two sections but leaving room for the catapults to be added later. Notice the mod below hadn’t had the front radar “fin” cut away from the rest of the tower yet.
    20190811_193457a.jpg

    The section of plastic on the launch catapult base that represents the recovery crane is only kept on the cut section long enough to measure the spacing of the 2nd stack before gluing. After it gets cut from the catapult base, the base is glued into place. After the glue dries, holes are drilled for the recovery crane (visible below- yes, FOlewnik got a drill small enough to go down the center of that tiny plastic pole to use it as the base of the recovery crane), the fore mast, and aft mast.
    DSC_0551a.jpg

    Two sizes of metal hobby rods (for lack of a better term- available at the hobby shop, little steel and brass rods) are used- a thick one that gets filed into a square for the launch catapults, and a thinner round one for the recovery crane and masts. On the fore mast, a square section of putty is used to make the radar screen, and on the aft mast, super glue gel is used to contour the top and mid section to resemble the silhouette of the New Orleans above. After adding the catapults to one piece to get an idea of how it will look (in the back below), FOlewnik decided to wait on the rest since painting around them would be difficult, if not frustrating. The five mods in various stages of completion:
    20190818_022406a.jpg

    To make the recovery crane’s chain, FOlewnik used synthetic brush hairs from a very large wooden handled scrub brush. They’re pretty much unbreakable, so it was a nice find. It gets super glued into place one section at a time then when dry, the excess is cut off. A drop of super glue gel at the end makes due for the recovery hook. Almost ready for primer, the one with catapults still needs some sanding.
    DSC_0548a.jpg

    When little pieces break or get lost, it’s nice to have the sprues from the Shapeways pieces to use and shape to one’s needs, as seen on the first mod below. The white catapult base was fashioned from sprue, and the large square glued onto the rear will be filed and shaped appropriately.
    DSC_0552a.jpg

    Sure enough, getting primer and paint around the catapults wasn’t easy, but FOlewnik got it done. These pieces will get the same treatment the Indy and Portland received. These five will be the New Orleans, Astoria, Minneapolis, Tuscaloosa, and San Francisco (yes, the Quincy and Vincennes are conspicuously absent but we will have the Astoria, which was sunk in the same battle).
    DSC_0571a.jpg

    These five are still in the process of being painted, along with the USS Cowpens (The Mighty Moo) and some more destroyers. When I went to visit FOlewnik at the end of our recent Labor Day weekend, he’d been away for a few days and just returned home. Apparently he was really nice to the spiders in his garage where his paint set up is, or they’re US Navy fans, because they tricked out some nice rigging on one of the ships, so of course I had to get a picture of it while it lasted.
    DSC_0569a.jpg

  • '20 '19 '18 Customizer

    The first New Orleans class cruiser is done (or was a few days ago but I’m just now getting around to posting). This one is the USS Minneapolis, CV-36.
    DSC_0610a.jpg
    DSC_0613a.jpg
    DSC_0615a.jpg

    The USS Minneapolis and the USS Indianapolis together for comparison:
    DSC_0616a.jpg
    DSC_0617a.jpg


  • Beautiful work!

  • '20 '19 '18 Customizer

    Thank you, Marc! While the rest of the New Orleans Class cruisers are getting done I wanted to share some more recent finishes. We’ve purchased some Independence Class aircraft carriers from Ebard at Shapeways for use as light carriers to go with HBG’s Casablanca light carriers, and the first one done is the USS Cowpens (CVL-25), also known as “The Mighty Moo” for its many Unit Awards, Campaign and Service Medals and Ribbons. There were a lot of references for the camo but very few for the deck and arresting cables. I was able to find a set of diagrams from some plastic model instructions, and with those and pictures of scale models and pictures of the class on Navsource.org FOlewnik was able to correctly place arresting gear on the flight deck. Although it’s a light carrier, it has 2 magnets for aircraft. To get better pictures of the sides, I put the piece on the edge of the board overhanging the table, but the first picture is when it was still in progress. I like it because you can better see the four colors used.
    DSC_0573a.jpg
    DSC_0595a.jpg
    DSC_0594a.jpg
    DSC_0598a.jpg
    DSC_0593a.jpg
    022506.jpg

    Also done is the USS Trenton (CL-11) from HBG in Camouflage Measure 33, Design 2F, from a set of drawings prepared by the Bureau of Ships for a camouflage scheme intended for light cruisers of the CL-4 (Omaha) class found on navsource.org.
    DSC_0599a.jpg
    DSC_0600-0401034.jpg
    DSC_0600a.jpg
    DSC_0600-0401033.jpg

    Another GHQ Benham Class destroyer is also done, this one as the USS Stack (DD-406). Her camouflage is Measure 31, Design 11d. Photographs from the Bureau of Ships Collection in the U.S. National Archives, via navsource.org.
    DSC_0602a.jpg
    DSC_0604-USS Stack-Benham Class.jpg
    DSC_0603a.jpg
    DSC_0604-USS Stack-Benham Class-0540609.jpg

    The three of them together:

    DSC_0589a.jpg
    DSC_0584a.jpg
    DSC_0591a.jpg
    DSC_0592a.jpg

  • '19 '18 '17

    Wow, this is some incredibly great work you are doing… And thank you so much for sharing!!!

  • '20 '19 '18 Customizer

    Thank you AA, we appreciate the compliment! FOlewnik completed the five New Orleans class cruisers 2 weeks ago, and between work and overtime we finally got together so I could add some roundels to the scout plane wings and add hull numbers to a few non-camouflage hulls. I took some shots before I added the decals, so from left to right, The USS New Orleans, USS Astoria, USS Tuscaloosa, USS San Francisco, and USS Minneapolis.
    DSC_0650a.jpg
    DSC_0653a.jpg
    DSC_0656a.jpg

    The USS New Orleans is wearing a Bow Wave camouflage pattern, and the USS Tuscaloosa and USS San Francisco are wearing Camouflage Measure 33, Design 13D from a diagram just like the Trenton above taken from navsource. The tiny roundels went on with very little fuss (which is unusual- I must be getting the hang of it) so adding decals went quicker than I thought it would.
    DSC_0658a.jpg
    DSC_0659a.jpg

  • '20 '19 '18 Customizer

    I finished a few more Hawker Hurricanes from SNAFU at Shapeways, so while FOlewnik is kept from his painting by all the overtime he’s got to put in at this time of year, I’ll share these.
    DSC_0662a.jpg
    DSC_0663a.jpg
    DSC_0666a.jpg
    DSC_0667a.jpg
    DSC_0668a.jpg

    A while back someone asked about storage and I tried to describe the old metal filing cabinet piece that FOlewnik found. I grabbed a couple of shots a while ago and forgot about them, so here they are. The drawers can fit 4 piece boxes in them, with the lids, 2x2. But the painted pieces don’t get tossed together, they get separated nicely, as in the Japanese Navy drawer shown here. We’ll eventually cut some foam for each drawer but for now this is how they are.
    DSC_0535.JPG
    DSC_0534.JPG

  • '20 '19 '18 Customizer

    Three Northampton Class cruisers are finished now, with a possible 4th being considered. As you can see from the comparison below, the out of box (OOB for those in the know) sculpt is suspiciously close to the Northampton silhouette taken from http://www.shipcamouflage.com/ships2_9_41_plate_15.htm, so comparatively little modification work was needed to the OOB sculpt.
    Comparison Northampton Vs Sculpt.jpg

    FOlewnik chose to paint the USS Northampton (CA-26) wearing Measure One (dark) camouflage, with a Measure Five false bow wave, as it wore when it returned to Pearl Harbor on Dec 8, 1941. There are great reference pictures for the false bow wave on navsource on the Northampton’s page: http://www.navsource.org/archives/04/026/04026.htm.
    DSC_0801a.jpg
    DSC_0802a.jpg
    DSC_0803a.jpg
    DSC_0806a.jpg

    If it weren’t sunk by Japanese aerial torpedoes off Rennell Island on 30 JAN 1943, The USS Chicago (CA-29) might have worn this camo pattern, and we needed a cruiser in this pattern, so FOlewnik painted the USS Chicago wearing US Navy Camo Measure 12:
    DSC_0827a.jpg
    DSC_0828a.jpg
    DSC_0829a.jpg

    Last but not least, from a drawing prepared by the Bureau of Ships for a camouflage scheme intended for heavy cruisers of the Northampton Class, here is the USS Chester (CA-27) wearing Camouflage Measure 32, Design 9D, as seen prominently on http://www.navsource.org/archives/04/027/04027.htm.
    DSC_0835a.jpg
    DSC_0836a.jpg

    The three Northampton Class cruisers together:
    DSC_0837a.jpg
    DSC_0839a.jpg

    And finally for comparison, the USS Chester (Northampton class), the USS Tuscaloosa (New Orleans class), and the USS Portland (Portland class):
    DSC_0840a.jpg

  • 2023 '22 '21 '20 '19 '18

    Northampton Victor Henry’s boat : ) Never heard of the false bow wave. I guess that was to make it look like it was going faster than it was ? Or is that just a customization thing ?


  • @barnee Yes, the idea was to give the illusion of speed. The USS Saratoga also wore bow wave camo for a while. Shipcamouflage.com actually uses the Northampton as an example here: http://www.shipcamouflage.com/measure_5.htm
    MS5_Northhampton.jpg

  • '20 '19 '18 Customizer

    USS Ranger (CV-4) by FOlewnik. He actually finished this around the time of the cruiser mods for the Northamptons but I’m just now getting around to editing the pictures to post. Sculpt is from Ebard at Shapeways. Although we’ll most likely use it as a light carrier, it still has 2 magnets.
    DSC_0814a.jpg
    DSC_0811a.jpg
    DSC_0812.JPG
    DSC_0818a.jpg
    DSC_0819a.jpg
    DSC_0821a.jpg

    Also done are the heavy cruiser USS Boston (CA-69) and the light cruiser USS Concord (CL-10), sculpts from HBG.
    DSC_0830a.jpg
    DSC_0833a.jpg

    I’ve been making aircraft for the US carriers, doing SBD’s from the out of box sculpts as seen earlier in the post, and as seen above atttached by magnet to the USS Ranger, HBG’s SB2C Helldivers. But I couldn’t find F4F’s. Undaunted, I took HBG’s Hellcats, which are smaller than the out-of-box Hellcats, and shaped the tail so it looked more like the top view of an F4F I found on Wings Palette (inset below). I used 400 sandpaper and made a few passes on each round end to flatten it out, then took an X-Acto knife and cut a nick next to the rudder and ran the sandpaper through a few times to create a groove between the rudder and rear wing. The test piece became Jimmy Thatch’s F4F. Tiny decal time (LESS than one millimeter!)- I used the bottom half of each side of an unused letter “H” for the dash between the “F” and the “1” on the fuselage, and to match the pictures on Wings Palette, the “1” is actually an upper case “i”, from the decal sheet LW-100 at HBG (https://www.historicalboardgaming.com/LW-100-Decal-Sheets-White-Lettering-All-scales_p_1839.html). Now I just need FOlewnik to finish the USS Lexington so it has a place to park.
    DSC_0798a.jpg
    Before the cockpit is inked:
    DSC_0823a.jpg
    After the cockpit is inked:
    DSC_0826a.jpg
    DSC_0826a3_6_b1.jpg

  • '20 '19 '18 Customizer

    Doolittle Raid USS Hornet (CV-8) by FOlewnik almost finished in these shots. It actually is finished (arrestor cables & AA guns missing here) but I don’t yet have pictures of it. FOlewnik is using Ebard’s Yorktown class for the sculpt. The unpainted sculpt shows where the magnets have been set and leveled with putty. You can see the hollow underside has also been filled. Prior to painting and drilling the magnet holes, the island bits that look fragile are brushed with liquid Super Glue (not the gel kind). Shapeways pieces are pretty porous so the glue soaks in and helps strengthen the piece.
    DSC_0842a.jpg

    Close up pf the deck lines. These are done with a 10/0 brush, both the black and white. The deck AA guns haven’t been done yet.
    DSC_0846a.jpg

    Side views:
    DSC_0848a.jpg
    DSC_0849a.jpg

    I’ve finally finished the decals on the 1/500 Spitfire MkI’s from SNAFU at Shapeways (https://www.shapeways.com/product/ZHFZWLMGK/spitfire-mk-ia-w-gear-x4-fud?optionId=66660049&li=marketplace) so I thought I’d share shots of those as well. They come with landing gear down like the Hawker Hurricanes shown earlier, but I’ve taken them off. They were used as funnels on the Japanese transports.
    DSC_0851a.jpg
    DSC_0857a.jpg
    DSC_0858a.jpg
    DSC_0860a.jpg

  • '20 '19 '18 Customizer

    USS Yorktown (CV-5) circa 1938 started as the unpainted Shapeways print in the above post alongside the unfinished USS Hornet. Hornet is shown finished here.
    DSC_0864a.jpg
    DSC_0866a.jpg
    DSC_0867a.jpg
    DSC_0865a.jpg
    DSC_0873a.jpg

    Port & starboard detail, USS Yorktown (CV-5):
    DSC_0869a.jpg
    DSC_0868a.jpg

    Port & starboard detail, USS Hornet (CV-8):
    DSC_0871a.jpg
    DSC_0870a.jpg

  • '20 '19 '18 Customizer

    USS Saratoga (CV-3) wearing Camouflage Measure 32 Design 11a, 3d print by Ebard at Shapeways, painted by FOlewnik. It has 2 magnets for aircraft hidden beneath the paint. Two photographs from 1944 are shown for reference.
    DSC_0915sara1944puget.jpg
    DSC_0915b.jpg
    DSC_0915a.jpg
    DSC_0913a.jpg
    DSC_0885a.jpg
    DSC_0887a.jpg
    DSC_0900a.jpg
    DSC_0901a.jpg
    DSC_0904b.jpg

    Short Stirling bombers from HBG painted by yours truly for the UK to use for long range or heavy bombers (or both). These are 1/600 scale, which is a little larger than the OOB bombers, but that gives room for more detail so I tried to take advantage of that. Each piece had to be heavily trimmed of flash plastic and mold grooves, and heated with a hair dryer to untwist and straighten out the fuselage and straighten the wings and rudder as best as possible. You can see a few rudders are still a little wilted, but compared to what they were, I was happy. From what I’ve been able to find in research, the actual bomber did not have counter rotating props like this sculpt does. These wear the markings of 7 Sqn, RAF, who were the first squadron to be equipped with the new Short Stirling heavy bomber, & the first RAF squadron to operate four engined bombers during the Second World War, flying the first bombing raids with the Stirling against oil storage tanks near Rotterdam on the night of 10/11 February 1941 (from the wiki).
    DSC_0924a.jpg
    DSC_0926a.jpg
    DSC_0927a.jpg
    DSC_0928a.jpg
    DSC_0933a.jpg

    I accented the control surfaces with the same 20/0 brush used for the fine cockpit lines, which are molded into the sculpt. First a dark wash of brown over the first coat of camo, then go over the wash with the original color again, and it helps mimic the fabric control surfaces. The top turret and front and rear turrets and bombardier’s window were done with the 005 black pen. Fuselage windows were done in silver with the Insane Detail brush from Army Painter and shaped after the first coat of dullcote with the black 005 pen if needed.
    DSC_0918a.jpg
    DSC_0920a.jpg
    DSC_0922a.jpg


  • @DMcLaren
    Beauty.
    Makes me want to rebuild my Lexingtons.

  • '16 Customizer

    @DMcLaren said in Custom carriers from OOB's and painted pieces:

    It’s been awhile since I’ve been on the forums and seen your customized work DMcLaren. Just now coming back to it… wow! What kinds of paints are you using that you can get such crisp lines? Are you thinning the paint at all to give yourself more definition on your lines? It looks amazing!

  • '20 '19 '18 Customizer

    Thank you, gentlemen. We- FOlewnik and I- appreciate the feedback.

    @Spitfire38 - It’s not the paint, it’s the brushes. FOlewnik does the ships with water based paint and I do the aircraft in enamel, both are finished with Testor’s Dullcote. FOlewnik relies heavily on his 10/0 brush for these US aircraft carrier decks, with help from his 20/0 and 0000 with the same on the hulls for camo detail and fine lines. I’d have to say I’m right around the same when I do the aircraft, but I do a lot with my incredibly old Testor’s 0 with a wooden handle. I’ve had it for about 40 years, now that I think about it! It (the zero brush) puts down the main coat on just about everything. My Army Painter brand “Psycho” and “Insane Detail” brushes are still in great shape and get a lot of use. The 20/0 I have did the cockpits for the SNAFU/Shapeways Hurricanes & Spitfires, and the above HBG Stirlings. I dip my 20/0 in whatever stays on the underside of the paint lid when the lid is set on the table. No thinner, clean brush. FOlewnik pours his paint onto one of those round plastic artist dishes with all the little round spaces for paint, one or two drops at a time, more if he’s doing a large area. He uses water based paint so he keeps the brush wet. It’s also important to “load” your brush properly- that is, to pick up the right amount of paint for what you want to do. If you have too much, paint the wooden holder to get rid of some, lol. If you notice FOlewnik’s ship holders that he made (angled pics of Sara above), they’re covered with paint stripes from where he’s removing paint from the brush and shaping the brush head to get a good point a lot of the time. But the idea is the smaller the detail wanted, the smaller the brush needed. It also helps to have a set of waterproof .005 pens, or just a black one if you can’t find a set of colors. Pens are best used after a base of dullcote to give the pen a smoother, porous surface to draw on. I still use pens, but FOlewnik has fallen in love with free-handing with a 20/0 paint brush and hasn’t used a pen since he finished the Japanese navy.
    DSC_0959-brushes&pens.jpg

  • '20 '19 '18 Customizer

    Five US Navy ships by FOlewnik- The USS Allen M Sumner (DD-692), the USS Pittsburgh (CA-72), USS Washington (BB-56), USS Massachusetts (BB-59), and my personal favorite of this particular post, the Essex class USS Yorktown (CV-10) from start to finish. To start, GHQ’s Sumner class destroyer as the Sumner itself, DD-692. GHQ pieces are made of pewter or similar alloy and are richly detailed. They’re five times the cost of an HBG piece, but they have a great variety of destroyers, too, so I guess you’re paying for variety and detail. They get painted quickly because they don’t need mods. FOlewnik bought several different DD types for the US Navy this past holiday season when orders over $100 got a fat discount, so the US Navy will have the hottest looking destroyer group when they’re all done. So here is the USS Allen M Sumner (DD-692):
    DSC_0910-USS ALLEN M SUMNER.jpg
    DSC_0911-USS ALLEN M SUMNER.jpg
    DSC_0912-USS ALLEN M SUMNER.jpg

    The USS Pittsburgh (CA-72) is a Historical Board Gaming Baltimore class heavy cruiser. These pieces have a lot of detail but need a lot of prep work with trimming flash plastic from where the molds leave a seam. These get modded with scout planes & recovery cranes and after FOlewnik gets done with them, look really good. This was done from a scale model guide, shown here.
    DSC_0946-USS Pittsburgh-0.jpg
    DSC_0945-USS Pittsburgh.jpg
    DSC_0946-USS Pittsburgh.jpg
    DSC_0944-USS Pittsburgh.jpg

    The USS Washington (BB-56) is the 2nd of the set from Ebard at Shapeways (there were 2 of this class). It also has the scout plane from GHQ added, and FOlewnik has added the life rafts during painting. It is painted as it looked during the Battle of Savo Island on the night of 14-15 November 1942.
    DSC_0939-BBWashington42SavoIsland.jpg
    DSC_0940-BBWashington42SavoIsland.jpg
    DSC_0942-BBWashington42SavoIsland.jpg

    HBG’s South Dakota Battleship is the basis for FOlewnik’s USS Massachusetts (BB-59). It required quite a bit of flash plastic trimming before the recovery crane was added. The scout planes from GHQ are painted separately and then glued in place before the tiny US star is added to the wings. Done to look like the ship appeared in July of 1942.
    DSC_0947-015928.jpg
    DSC_0947-USS Massachusetts (BB-59).jpg
    DSC_0951-USS Massachusetts (BB-59).jpg
    DSC_0953-USS Massachusetts (BB-59).jpg

    HBG’s Essex class carrier is the basis for FOlewnik’s USS Yorktown (CV-10). The bare sculpt had to be cleaned and prepped- you can see the brown putty added to level the deck. Magnets are glued in flush with the flight deck. In the second picture, you can see FOlewnik’s 10/0 brush used on the flight deck to the left, and at right is his paint palette with the paint wells.
    DSC_0908-USS Yorktown CV-10.jpg
    DSC_0954-USS Yorktown CV-10.jpg
    DSC_0963-USS Yorktown CV-10.jpg
    DSC_0965-USS Yorktown CV-10.jpg
    DSC_0968uss yorktown camo.jpg
    DSC_0967-USS Yorktown CV-10.jpg
    DSC_0966-USS Yorktown CV-10.jpg
    DSC_0968-USS Yorktown CV-10.jpg
    DSC_0971-USS Yorktown CV-10.jpg
    DSC_0969-USS Yorktown CV-10.jpg


  • @DMcLaren test


  • The artist appears!

Suggested Topics

Axis & Allies Boardgaming Custom Painted Miniatures

33

Online

17.0k

Users

39.3k

Topics

1.7m

Posts