Welcome! If you're a returning member of the forums, please reset your password. If you don't receive an email within minutes, it means your account is listed under another, likely older, email address. Contact webmaster@axisandallies.org for help.

Custom carriers from OOB's and painted pieces


  • 2018 Customizer

    The Pearl Harbor versions of the Zuikaku & Shokaku with their later war versions (from the first picture in the post on page 1).  That the Zuikaku camo version is an out of box Shinano really bothered FO, and that’s what started the whole “chop off this tower and swap that one in here, and maybe add a little putty here for more deck guns and cut away under the flight deck” ideas.  All of these started as Shinano sculpts (and the one still is).  The side view picture is the same ship on the left top & bottom, and right top & bottom.

    IJN Zuikaku Shokaku.jpg
    IJN Zuikaku Shokaku side.jpg


  • 2018 Customizer

    We really liked HBG’s Nagara light cruisers and bought 2 sets (3 are left to paint).  While researching paint schemes, we noticed the real ships have a plane on a launch catapult. So FJO made launch catapults for some Nagaras and bought a carrier from GHQ for the planes and antennae towers, and put planes on some of the launch catapults.  Little GHQ aircraft ended up going on a lot of other IJN ships, too.

    IJN Nagara Light Cruiser.jpg


  • 2018 Customizer

    The IJN Takaos from earlier in the post got a face lift (top picture), and 4 unpainted ones were modded into Mogami class cruisers, with launch catapults and a recovery crane (bottom picture).  The Tone has 4 little aircraft on it (bottom picture).

    IJN Takao.jpg
    IJN Mogami.jpg


  • 2018 Customizer

    We have 3 cruiser types in our house rules- light cruisers, cruisers, and heavy cruisers.  These IJN Heavy Cruisers are 1st Ed. A&A Battleships that FJO painted as if they were Japanese warships, adding a lot of detail that’s not in the sculpt, both with paint and by adding left-over guns from the GHQ carrier.  There’s no historical basis for these ships and there wasn’t a schematic available to make the sculpt Japanese, so he just winged it.

    IJN A&A 1st Ed BB.jpg
    IJN A&A 1st Ed BB top.jpg


  • 2018 Customizer

    The IJN Kongo class battleships.  They have a launch catapult molded in, so of course they got planes.  We just got a mixed set of 2 Nagato battleships and 3 Fuso battleships from HBG (yes, they’ll split their sets of 5 for you) and will be using the Fusos for heavy cruisers. The Nagatos will be added to the BB set. And here’s a better picture of the Yamato, showing some wear as the red primer pokes through. You may have noticed some ships camo’d with an orange and yellow curved stripe- those are from a camo fleet, the pattern found called “Fleet of Fog”.  Google it to see what these ships were based on.

    IJN Kongo Class BB.jpg
    IJN Yamato.jpg


  • 2018 2017 2016 2015 Customizer

    Pretty amazing work. How long does it take to do a typical ship with all that detail?


  • 2018 Customizer

    Hard to say, really, LHoffman, since there are many being worked on at the same time in various stages of preparation or finish. Consider: Most of the little silver dots on the decks to represent deck guns are built up layers of pigment, so the flat surface of the sculpt is broken up with little bumps.  On average, 7-10 applications of pigment make a deck gun bump, and each layer has to dry before the next one is applied.  FJO has a series of pictures of the making of the Mogami cruisers, so I’ll have to get hold of those to post.  Those 4 took a few weeks, but they weren’t worked on every day.  And they had to wait for the Pearl Harbor versions of the Zuikaku and Shokaku to get finished.  Those, I know, took a long time.  The towers have been replaced, the hull was cut away under the fore and aft flight decks, both have hand drawn & painted hull illustrations port & starboard accurate to the schematics, the decks are hand painted (not decals), putty has been added to each side of the flight deck and then sculpted away to make more deck AA guns and place them accurately according to the schematic.  Like I said, those took a long time.  Over the coarse of 2 months at least, while other things were going on, like the Kongos getting base colors.  FO called as I was typing this, so I asked about average time per ship.  The answer, after some consideration of research, amount of modification, and detail, was 8-15 hours per ship, at about 5-10 hours per week.  Given what’s been done and what I know of the time so far, I’d say if we had the real number of ships and time and did the math, it wouldn’t work out to the estimate.  Either less hours per ship or more hours per week, I’d say.

    And thanks, I think, for the compliment, Nowhere Man.  Remember, ours is a 2 man project.  I only get to spend an hour or three during the weekdays painting, and maybe a half-day on the weekend.  So 5-10 hours per week for me.  I’m doing the aircraft (mostly so we can play “Check Your 6!” with the lego flight stands I made) and FJO is doing ships (so we can use them for table top “Victory at Sea” also).


  • 2017 2016 Customizer

    WOW! These are fantastic! I love seeing the life boats on them, thanks for sharing.


  • 2019 2018 Customizer

    Insane level of detail on these ships! Well done.

    How many years of painting miniatures do you have behind you?


  • 2018 Customizer

    Thanks, guys.  I was impressed when I saw the lifeboats, too- they’re better in person because they’re built up with lots of layers of pigment so they look like they’re molded in on the sculpt (well, they actually are on HBG’s Nagara light cruisers).  I’m trying to up the level of detail on the aircraft I’m doing for our set to match FJO’s IJN level of detail.  I especially like the top down view of the 1st edition battleships to see the detail he’s added.  Years of experience?  FJO has been a professional painter for a few decades now (see brief description in opening post), and we’re both in our mid 50’s & started painting our D&D miniatures back when we were in high school.

    I’ve mentioned one of the 18 decal Stukas in another post, as well as HBG’s JU-87G Stukas that I like so much, so since these are done I thought I’d share some shots of them.

    Germ Stuka JU-87AA JU87G.jpg
    Germ Stuka JU-87G JU87AA.jpg


  • 2018 Customizer

    I just finished this piece last night and I’m so happy with it that I wanted to share it here.  Bit of back story- while researching aircraft paint schemes I came across a game called “Check Your 6!”.  One of the scenarios in that game is based on a real encounter wherein pilot “The Swede” Vejtasa in an SBD from the Yorktown, while on submarine patrol, shot down 3 Zeros in an engagement.  With magnets in our aircraft for the carriers, we were half way to playing CY6 anyway, so I got some Legos from their website and some acorn nuts from the hardware store and made flight stands.  So of course I had to make Vejtasa’s SBD.  I got REALLY lucky with i-94 decals for this project.  Their sheet of American flags has one the perfect size to be cut down for the red and white striped rudder of this SBD- 7 red stripes from the top tip of the rudder down to the rear wings at the base of the rudder.  Measure twice, cut once for a perfect fit front to back.  That saved me a ton of time and headache on an accurate rudder.  And i-94’s sheet of black letters and numbers had numbers the perfect size for the fuselage and tail.  The one thing that was sort of bummer is that their US roundels come with the red dot as a separate decal that you have to add and perfectly, and I mean PERFECTly, center in the star to make it look right.  So because there wasn’t a “10” decal on the sheet, the 1 and the 0 are 2 separate decals, as are each US star & dot roundel and each half of the rudder, making this aircraft number one in number of decals with twenty decals total.  There are tons of references for this aircraft all over the internet that helped a lot in drawing the cockpit.  I used the .005 pen rather than the 20/0 brush with fuselage color so it would pop better and help make the aircraft more recognizable as what it is.  Decal sheets used are (copy &  pasted from HBG’s site) Black Lettering Decal Sheets (LB-100), U.S. Flags (US-118), U.S. Star on blue field (US-102).  Base of the stand is a Lego radar dish.

    US the Swede SBD.jpg
    US the Swede SBDa.jpg


  • 2018 2017 2016 2015 Customizer

    Really, superb work. These are really good. 🙂


  • 2018 Customizer

    IJN Nagato & Mutsu from HBG.  Roughly 18 hours on each piece by FJO’s estimate.  There was a discussion whether to include gun barrels on the deck guns- I thought the ships looked great without, and then saw them with them in and it made a huge difference.  They fit better alongside the Kongo BB’s with the barrels added.  I found a schematic and a nice picture of a large scale model and printed those for paint references and gave the print to FJO, shown below.  Each has a launch catapult added, one angled for launch that will get a small plane, and the other in neutral position that won’t have a plane.  The flash washes out some of the contrast on the pieces so it may be a bit difficult to see there are 3 different greys on the hulls, and 2 and 3 colors of the same shade on each respectively on the deck colors.  As with all HBG pieces, these have a lot of nice detail molded in and FJO highlighted all those, like the deck guns, and added more things like the life boats shown on the schematic and model picture, and rails on the catapult deck and other small details.  I kept trying to get a picture with both ships in focus but the camera didn’t want to cooperate, so I just combined the best shots into one, with different ships in better focus in each.  Best viewed by right clicking and opening in a new frame.

    IJN Nagato & Mutsu.jpg
    japan nagatoImage2.jpg


  • 2018 Customizer

    IJN Nagato & Mutsu rear view and top view for a better view of the deck detail.

    IJN Nagato & Mutsu 1.jpg
    IJN Nagato & Mutsu top.jpg


  • 2018 Customizer

    IJN Fuso class ships from HBG.  We’re using them as heavy cruisers.  Lots of nice detail in the sculpt but the deck guns are only molded in on one side so FJO had to make them on the other side to match the schematic I found for him online.  He calculated roughly 25 hours on these 3 pieces over the last 2 weeks.  That time may also include the conning tower makeover and plane on the launch catapult for the Mutsu, but I forgot to ask.

    IJN Fuso class BB front-side.jpg
    IJN Fuso class BB rear-top.jpg


  • 2018 Customizer

    Here’s the Mutsu after the front base of the conning tower was redone and the scout plane was added to the launch catapult.  Compare this shot with the ones from earlier and you can really see the difference on the front tower and the scout plane area.

    IJN Mutsu with scout plane.jpg


  • 2018 Customizer

    I got a hold of the shots of the Mogami cruisers in progress and wanted to share them to show the mods that were done.  One turned out to be a Tone class, so it’s actually 3 Mogami class and 1 Tone.  As with all the sculpts, they started with a coat of primer (red in this case), and then the flashing is trimmed and any uneven edges between halves of the sculpt are leveled.  Mogamis had smaller conning towers than the Takao class these were made from, so the towers were cut off and sanded down before being glued back in place.  While they were off, the smoke stacks got filed in front and top, and putty was added between them to match the profile on the schematic of the Mogami smoke stacks.  Holes were drilled to accept a small brass rod for the scout plane retrieve crane, and sections of the round rod were squared with a file to make the crane arm, then super glued to the round rod to complete the crane.  More small sections were squared with a file to make the launch catapults that were glued in later. (A few of my Oscars are in the top picture waiting to get their canopies done.)  These are pretty big files best viewed by right clicking and opening in another window.

    IJN Mogami in progress.jpg
    IJN Mogami in progress1.jpg


  • 2018 Customizer

    The Mogamis also got more putty added to the sides to make the bulges where the catapult launch arm is attached and the extra port and starboard AA guns were added.  The putty is formed while it’s still soft to as close a shape as it can get, then sculpted and filed after it hardens.  The launch catapults for the scout planes have been added above the bulge they hinge from, and the extra forward deck guns taken from the GHQ carrier have also been added.

    IJN Mogami & Kumano in progress.jpg
    IJN Mogami & Kumano in progress1.jpg


  • 2018 Customizer

    The little tiny planes from GHQ were painted before they were super glued into place, and another look at the four from the rear to see the aircraft.

    20171202_224406(1).jpg
    DSCN1532.JPG


  • 2018 Customizer

    I wanted to post these last Sunday but that Midwest ice storm knocked out the power for 3 days.  FJO has started doing the Japanese transports after a bit of research into the sculpts.  He found a lot of pictures of Japanese merchant ships that the game sculpts are based on, so he’s going to do a bunch of different paint schemes matching the various pictures to make each transport different from the rest.  The first one, a sculpt from A&A '41, is done up as the Kita Maru.  This was started Friday and finished Saturday.

    IJN Kita Maru start.jpg
    IJN Kita Maru bow.jpg


  • 2018 Customizer

    The Kita Maru port & starboard.

    IJN Kita Maru port.jpg
    IJN Kita Maru starboard.jpg


  • 2018 Customizer

    Next up is the other Japanese transport sculpt from the most recent 2nd Ed., this one done as the IJN Nagitsu Maru.

    IJN Nagitsu Maru bow stern top.jpg
    IJN Nagitsu Maru port & starboard.jpg


  • 2018 Customizer

    Rolling Advanced Artillery in our house rules opens up tank killers- the JU-87G from HBG shown earlier is the only flying tank killer we can find a sculpt for.  The British put some 40mm cannon on a Hurricane and called it a Mk IID, so I grabbed a section of FJO’s little brass rods he uses for his mods and cut some cannons and super glued (with gel so it left a nice thick coat) them under the wings of one of the Hurricanes I got from Shapeways.  Paint scheme is based on a Mk IV found on Wings Palette (which is a great source for aircraft paint and decal references: http://wp.scn.ru/en/ww2/f/79/9/16).

    UK Hurricane MkIID-1.jpg
    UK Hurricane MkIID.jpg


  • 2018 Customizer

    FJO has been knockin’ out the transports lately.  These two were done last week- the Takatsu Maru and the Kinjosan Maru.  There’s some added putty on the Takatsu Maru- just a little in the center of the top.

    IJN Takatsu Maru.jpg
    IJN Kinjosan Maru.jpg


  • 2018 Customizer

    The Teia Maru has a lot of room for troops to travel in comfort.  FJO also finished the last 2 Japanese aircraft- one of Egusa Takeshige’s Vals and a Ki-43 Oscar.  I saved those 2 for him to paint after I did the rest of the IJAF and it took him almost a year to get to them, but he did them proud.

    IJN Teia Maru.jpg
    FJO Val Oscar.jpg


Log in to reply
 

Welcome to the new forums! For security and technical reasons, we did not migrate your password. Therefore to get started, please reset your password. You may use your email address or username. Please note that your username is not your display name.

If you're having problems, please send an email to webmaster@axisandallies.org

T-shirts, Hats, and More

Suggested Topics

  • 8
  • 15
  • 12
  • 6
  • 9
  • 120
  • 15
  • 17
I Will Never Grow Up Games

31
Online

13.2k
Users

33.4k
Topics

1.3m
Posts